The Turbomeca Astazou is a highly successful series of turboprop and turboshaft engines, first run in 1957. The original version weighed 110kg (243lb) and developed 240kW (320shp) at 40,000 rpm. It was admitted for aviation service on May 29, 1961, after a 150-hour test run. The main developing engineer was G. Sporer. It was named after two summits of the Pyrenees.
This article includes a list of general references, but it lacks sufficient corresponding inline citations. (July 2011)
A simplified version was built by Agusta as the Turbomeca-Agusta TA.230.
Design and development
The Astazou IIA version was derived from the original Astazou powerplant for use in helicopters. By 1993, 2,200 had been built. As of 2007, it was still in production. However, many aircraft initially equipped with it, especially the heavier ones, have since been upgraded with more powerful engines.
The early single-shaft Astazou has a two-stage compressor, with the first stage an axial and the second stage a radial design. It has an annular combustion chamber, after which the combustion gases enter a three-stage axial turbine.
Engines have a reduction gearbox in front of the air inlet, with an output speed suitable for a propeller or, for helicopters, as the first stage only of the much bigger reduction required for a rotor. Fuel to the gas generator is adjusted automatically to maintain a constant propeller or rotor speed as blade pitch varies.
Handley Page HP.137 Jetstream, with twin Astazou XIV, showing the distinctive annular air inlet and long reduction gear housing
As of the Astazou X, the engine received a second axial compressor stage. This was the engine for the Potez 840. The Astazou XIV and XVI were also marketed by Rolls-Royce Turboméca International Ltd under the names AZ14 and AZ16, respectively.
Power was steadily increased over the years, with the Eurocopter Dauphin's dual Astazou XVIII developing 783kW each. The Astazou XX received a third axial stage, raising compression even further to achieve a projected output of 1,075kW (1,442hp) in the turboprop application. The XXB derivative, used in the single engine Aérospatiale SA 361H Dauphin, delivered 1,043kW (1,399shp).
Variants
Astazou I
Astazou II
Single-stage axial plus single-stage centrifugal compressor, annular combustor, three-stage turbine
Astazou IIA
Astazou III
Astazou IIIA
Astazou IIIC
Astazou IIIC2
Astazou IIIN
Astazou IIIN2
Astazou VI
Coupled Astazou 1,100kW (1,480shp)
Astazou X
The X and subsequent engines had a second axial compressor stage added.
Astazou XII
Astazou XIV
Two-stage axial plus single-stage centrifugal compressor, annular combustor, three-stage turbine. Integral front mounted
gearbox.
Astazou XIVA
Astazou XIVB
Astazou XIVD
Astazou XIVC
Astazou XIVH
Astazou XIVM
Astazou XVI
Astazou XVIII
Astazou XVIIIA
Astazou XX
A third axial compressor stage added for increased pressure ratio.
Astazou XXB
Turbomeca-Agusta TA.230
(aka TAA-230)A simplified version built by Agusta.[1]
Rolls-Royce Turboméca AZ14
The Astazou XIV marketed by Rolls-Royce Turboméca International Ltd as the AZ14
Rolls-Royce Turboméca AZ16
The Astazou XVI marketed by Rolls-Royce Turboméca International Ltd as the AZ16
Другой контент может иметь иную лицензию. Перед использованием материалов сайта WikiSort.org внимательно изучите правила лицензирования конкретных элементов наполнения сайта.
2019-2025 WikiSort.org - проект по пересортировке и дополнению контента Википедии